-- *********************************************************************
-- CISCO-PROP-ATM-IF-MIB: This mib is for propAtm port interface
--
-- April 2002, Yizhong Shen
--
-- Copyright (c) 2002 by cisco Systems, Inc.
-- All rights reserved.
-- *********************************************************************CISCO-PROP-ATM-IF-MIB DEFINITIONS::=BEGIN
IMPORTSMODULE-IDENTITY,OBJECT-TYPE,Integer32,Counter32,
Counter64,Unsigned32FROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ifIndex FROM IF-MIB
ciscoMgmt FROM CISCO-SMI;ciscoPropAtmIfMIB MODULE-IDENTITYLAST-UPDATED"200212040000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-voice-gateway@cisco.com"DESCRIPTION"This MIB is designed for Propietary ATM (propAtm)
interfaces.
The propAtm interfaces are identified in the ifTable
entries with ifType 197 (as defined in IANAifType-MIB).
This interface is a switch virtual interface which does
not have any physical connector(jack).
"REVISION"200212040000Z"DESCRIPTION"Initial version of this MIB module."::={ciscoMgmt 319}ciscoPropAtmIfMIBNotifs OBJECTIDENTIFIER::={ ciscoPropAtmIfMIB 0}ciscoPropAtmIfMIBObjects OBJECTIDENTIFIER::={ ciscoPropAtmIfMIB 1}cpAtmIfConfig OBJECTIDENTIFIER::={ ciscoPropAtmIfMIBObjects 1}
cpAtmIfVirtualPortStats OBJECTIDENTIFIER::={ ciscoPropAtmIfMIBObjects 2}-- *********************************************************************
-- cpAtmIfConfigTable
-- *********************************************************************cpAtmIfConfigTable OBJECT-TYPESYNTAXSEQUENCEOF CpAtmIfConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table is used to configure propAtm interfaces.
Each entry in this table has a corresponding ifTable
entry with ifType propAtm(197). The ifIndex value
of that associated ifTable entry is used to index
this this table.
The entry of this table is added after its associated
ifEntry is added in the ifTable of IF-MIB.
It is impossible to add/delete entry to/from this table.
"::={ cpAtmIfConfig 1}cpAtmIfConfigEntry OBJECT-TYPESYNTAX CpAtmIfConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the cpAtmIfConfigTable table for
each propAtm port interface.
."INDEX{ ifIndex }::={ cpAtmIfConfigTable 1}
CpAtmIfConfigEntry ::=SEQUENCE{
cpAtmIfMaxBandwidth Unsigned32}cpAtmIfMaxBandwidth OBJECT-TYPE
SYNTAXUnsigned32(0..4294967295)UNITS"cells-per-second"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The propATM interface's maximum cell rate.
"DEFVAL{7000000}::={ cpAtmIfConfigEntry 1}-- *********************************************************************
-- cpAtmIfStatsEgressTable
-- *********************************************************************cpAtmIfStatsEgressTable OBJECT-TYPESYNTAXSEQUENCEOF CpAtmIfStatsEgressEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"This table reflects real-time statistics associated with
each of propAtm interfaces on the egress side.
Ingress terminology is used for the cells that are generated
by the voice gateway on the TDM side and are going toward
the ATM switch.
Egress terminology means the cells that are coming from the
ATM switch into the TDM side. This table contains
statistics from this egress point of view.
"::={ cpAtmIfVirtualPortStats 1}cpAtmIfStatsEgressEntry OBJECT-TYPESYNTAX CpAtmIfStatsEgressEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the cpAtmIfStatsEgressTable table for
each propAtm port interface.
CLP-0 means Cell Loss Priority = 0,
CLP-1 means Cell Loss Priority = 1.
"INDEX{ ifIndex }::={ cpAtmIfStatsEgressTable 1}
CpAtmIfStatsEgressEntry ::=SEQUENCE{
cpAtmIfEgrRcvClp0Cells Counter32,
cpAtmIfEgrRcvClp1Cells Counter32,
cpAtmIfEgrClp0DiscCells Counter32,
cpAtmIfEgrClp1DiscCells Counter32,
cpAtmIfEgrRcvOAMCells Counter32,
cpAtmIfEgrRcvEFCICells Counter32,
cpAtmIfHCEgrRcvClp0Cells Counter64,
cpAtmIfHCEgrRcvClp1Cells Counter64,
cpAtmIfHCEgrClp0DiscCells Counter64,
cpAtmIfHCEgrClp1DiscCells Counter64,
cpAtmIfHCEgrRcvOAMCells Counter64,
cpAtmIfHCEgrRcvEFCICells Counter64}cpAtmIfEgrRcvClp0Cells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells received from switch
at the traffic management and policing device.
"::={ cpAtmIfStatsEgressEntry 1}cpAtmIfEgrRcvClp1Cells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of CLP-1 cells received from switch
at the traffic management and policing device.
"::={ cpAtmIfStatsEgressEntry 2}cpAtmIfEgrClp0DiscCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells discarded due to policing.
"::={ cpAtmIfStatsEgressEntry 3}cpAtmIfEgrClp1DiscCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells discarded due to policing.
"::={ cpAtmIfStatsEgressEntry 4}cpAtmIfEgrRcvOAMCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of OAM cells received from the switch
at the traffic management and policing device.
"::={ cpAtmIfStatsEgressEntry 5}cpAtmIfEgrRcvEFCICells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells received from the switch
at traffic management and policing device.
"::={ cpAtmIfStatsEgressEntry 6}--
-- High Capacity Counter objects. These objects are all
-- 64 bit versions of the "basic" counters. These
-- objects all have the same basic semantics as their 32-bit
-- counterparts, however, their syntax has been extended
-- to 64 bits.
--cpAtmIfHCEgrRcvClp0Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells received from switch
at the traffic management and policing device.
This object is a 64-bit version of
cpAtmIfEgrRcvClp0Cells.
"::={ cpAtmIfStatsEgressEntry 7}cpAtmIfHCEgrRcvClp1Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells received from switch
at the traffic management and policing device.
This object is a 64-bit version of
cpAtmIfEgrRcvClp1Cells.
"::={ cpAtmIfStatsEgressEntry 8}cpAtmIfHCEgrClp0DiscCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells discarded due to policing.
This object is a 64-bit version of
cpAtmIfEgrClp0DiscCells.
"::={ cpAtmIfStatsEgressEntry 9}cpAtmIfHCEgrClp1DiscCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells discarded due to policing.
This object is a 64-bit version of
cpAtmIfEgrClp1DiscCells.
"::={ cpAtmIfStatsEgressEntry 10}cpAtmIfHCEgrRcvOAMCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of OAM cells received from the switch
at the traffic management and policing device.
This object is a 64-bit version of
cpAtmIfEgrRcvOAMCells.
"::={ cpAtmIfStatsEgressEntry 11}cpAtmIfHCEgrRcvEFCICells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells received from the switch
at traffic management and policing device.
This object is a 64-bit version of
cpAtmIfEgrRcvEFCICells.
"::={ cpAtmIfStatsEgressEntry 12}-- *********************************************************************
-- cpAtmIfEgressIntervalTable
-- *********************************************************************cpAtmIfEgressIntervalTable OBJECT-TYPE
SYNTAXSEQUENCEOF CpAtmIfEgressIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table reflects interval(each 15 minute) statistics
associated witheach of the propAtm interfaces on egress side.
"::={ cpAtmIfVirtualPortStats 2}cpAtmIfEgressIntervalEntry OBJECT-TYPESYNTAX CpAtmIfEgressIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the cpAtmIfEgressIntervalTable table
for each propAtm port interface.
CLP-0 means Cell Loss Priority = 0,
CLP-1 means Cell Loss Priority = 1.
"INDEX{ ifIndex, cpAtmIfEgressIntervalNumber}
::={ cpAtmIfEgressIntervalTable 1}
CpAtmIfEgressIntervalEntry ::=SEQUENCE{
cpAtmIfEgressIntervalNumber Integer32,
cpAtmIfIntEgrRcvClp0Cells Counter32,
cpAtmIfIntEgrRcvClp1Cells Counter32,
cpAtmIfIntEgrClp0DiscCells Counter32,
cpAtmIfIntEgrClp1DiscCells Counter32,
cpAtmIfIntEgrRcvOAMCells Counter32,
cpAtmIfIntEgrRcvEFCICells Counter32,
cpAtmIfHCIntEgrRcvClp0Cells Counter64,
cpAtmIfHCIntEgrRcvClp1Cells Counter64,
cpAtmIfHCIntEgrClp0DiscCells Counter64,
cpAtmIfHCIntEgrClp1DiscCells Counter64,
cpAtmIfHCIntEgrRcvOAMCells Counter64,
cpAtmIfHCIntEgrRcvEFCICells Counter64}cpAtmIfEgressIntervalNumber OBJECT-TYPESYNTAXInteger32(1..96)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Index of the table which represents the interval number.
An interval number between 1 and 96, where 1 is the
most recently completed 15 minute interval and 96 is
the 15 minutes interval completed 23 hours an 45
minutes prior to interval 1.
"::={ cpAtmIfEgressIntervalEntry 1}cpAtmIfIntEgrRcvClp0Cells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells received from switch
at the traffic management and policing device
during a 15 minute interval.
"::={ cpAtmIfEgressIntervalEntry 2}cpAtmIfIntEgrRcvClp1Cells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells received from switch
at the traffic management and policing device
during a 15 minute interval.
"::={ cpAtmIfEgressIntervalEntry 3}cpAtmIfIntEgrClp0DiscCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells discarded due to policing
during a 15 minute interval.
"::={ cpAtmIfEgressIntervalEntry 4}cpAtmIfIntEgrClp1DiscCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells discarded due to policing
during a 15 minute interval.
"::={ cpAtmIfEgressIntervalEntry 5}cpAtmIfIntEgrRcvOAMCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of OAM cells received from the switch
at the traffic management and policing device
during a 15 minute interval.
"::={ cpAtmIfEgressIntervalEntry 6}cpAtmIfIntEgrRcvEFCICells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells received from the switch
at traffic management and policing device during a 15
minute interval.
"::={ cpAtmIfEgressIntervalEntry 7}--
-- High Capacity Counter objects. These objects are all
-- 64 bit versions of the "basic" counters. These
-- objects all have the same basic semantics as their 32-bit
-- counterparts, however, their syntax has been extended
-- to 64 bits.
--cpAtmIfHCIntEgrRcvClp0Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells received from switch
at the traffic management and policing device
during a 15 minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrRcvClp0Cells.
"
::={ cpAtmIfEgressIntervalEntry 8}cpAtmIfHCIntEgrRcvClp1Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells received from switch
at the traffic management and policing device
during a 15 minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrRcvClp1Cells.
"::={ cpAtmIfEgressIntervalEntry 9}cpAtmIfHCIntEgrClp0DiscCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells discarded due to policing
during a 15 minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrClp0DiscCells.
"::={ cpAtmIfEgressIntervalEntry 10}cpAtmIfHCIntEgrClp1DiscCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells discarded due to policing
during a 15 minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrClp1DiscCells.
"::={ cpAtmIfEgressIntervalEntry 11}cpAtmIfHCIntEgrRcvOAMCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of OAM cells received from the switch
at the traffic management and policing device
during a 15 minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrRcvOAMCells.
"::={ cpAtmIfEgressIntervalEntry 12}cpAtmIfHCIntEgrRcvEFCICells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells received from the switch
at traffic management and policing device during a 15
minute interval.
This object is a 64-bit version of
cpAtmIfIntEgrRcvEFCICells.
"::={ cpAtmIfEgressIntervalEntry 13}
-- *********************************************************************
-- cpAtmIfStatsIngressTable
-- *********************************************************************cpAtmIfStatsIngressTable OBJECT-TYPESYNTAXSEQUENCEOF CpAtmIfStatsIngressEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table reflects real time statistics associated with
each of the the propAtm interfaces on the ingress side.
Ingress terminology is used for the cells that are generated
by the voice gateway on the TDM side and are going toward
the ATM switch.
Egress terminology means the cells that are coming from the
ATM switch into TDM side. This table contains statistics
from this ingress point of view.
"::={ cpAtmIfVirtualPortStats 3}
cpAtmIfStatsIngressEntry OBJECT-TYPESYNTAX CpAtmIfStatsIngressEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the cpAtmIfStatsIngressTable table for
each propAtm port interface.
CLP-0 means Cell Loss Priority = 0,
CLP-1 means Cell Loss Priority = 1.
"INDEX{ ifIndex }::={ cpAtmIfStatsIngressTable 1}
CpAtmIfStatsIngressEntry ::=SEQUENCE{
cpAtmIfIngXmtClp0Cells Counter32,
cpAtmIfIngXmtClp1Cells Counter32,
cpAtmIfIngXmtEFCICells Counter32,
cpAtmIfIngXmtOAMCells Counter32,
cpAtmIfHCIngXmtClp0Cells Counter64,
cpAtmIfHCIngXmtClp1Cells Counter64,
cpAtmIfHCIngXmtEFCICells Counter64,
cpAtmIfHCIngXmtOAMCells Counter64}cpAtmIfIngXmtClp0Cells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-0 cells transmitted to the switch
after traffic management and policing in
ingress direction."::={cpAtmIfStatsIngressEntry 1}cpAtmIfIngXmtClp1Cells OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells transmitted to the switch
after traffic management and policing in
ingress direction."::={cpAtmIfStatsIngressEntry 2}cpAtmIfIngXmtEFCICells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells transmitted to the switch
after traffic management and policing in
ingress direction."::={cpAtmIfStatsIngressEntry 3}
cpAtmIfIngXmtOAMCells OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of OAM loopback cells transmitted to switch
after traffic management and policing in
ingress direction."::={cpAtmIfStatsIngressEntry 4}--
-- High Capacity Counter objects. These objects are all
-- 64 bit versions of the "basic" counters. These
-- objects all have the same basic semantics as their 32-bit
-- counterparts, however, their syntax has been extended
-- to 64 bits.
--cpAtmIfHCIngXmtClp0Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The number of CLP-0 cells transmitted to the switch
after traffic management and policing in
ingress direction.
This object is a 64-bit version of
cpAtmIfIngXmtClp0Cells.
"::={cpAtmIfStatsIngressEntry 5}cpAtmIfHCIngXmtClp1Cells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of CLP-1 cells transmitted to the switch
after traffic management and policing in
ingress direction.
This object is a 64-bit version of
cpAtmIfIngXmtClp1Cells.
"::={cpAtmIfStatsIngressEntry 6}cpAtmIfHCIngXmtEFCICells OBJECT-TYPESYNTAXCounter64
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of EFCI cells transmitted to the switch
after traffic management and policing in
ingress direction.
This object is a 64-bit version of
cpAtmIfIngXmtEFCICells.
"::={cpAtmIfStatsIngressEntry 7}cpAtmIfHCIngXmtOAMCells OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of OAM loopback cells transmitted to switch
after traffic management and policing in
ingress direction.
This object is a 64-bit version of
cpAtmIfIngXmtOAMCells."::={cpAtmIfStatsIngressEntry 8}
-- *********************************************************************
-- conformance information
-- *********************************************************************cpAtmIfMIBConformance
OBJECTIDENTIFIER::={ ciscoPropAtmIfMIB 2}cpAtmIfMIBCompliances
OBJECTIDENTIFIER::={ cpAtmIfMIBConformance 1}cpAtmIfMIBGroups
OBJECTIDENTIFIER::={ cpAtmIfMIBConformance 2}--
--Conformance and compliance statements
--cpAtmIfMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION
"The compliance statement for the SNMP entities which implement
ciscoPropAtmIfMIB."MODULE-- this moduleMANDATORY-GROUPS{
cpAtmIfConfigGroup
}GROUP cpAtmIfEgressStatMIBGroup
DESCRIPTION"This group is for the counters with a 32-bit version."GROUP cpAtmIfEgressIntervalMIBGroup
DESCRIPTION"This group is for the counters with a 32-bit version."GROUP cpAtmIfIngressStatMIBGroup
DESCRIPTION"This group is for the counters with a 32-bit version."GROUP cpAtmIfHCEgressStatMIBGroup
DESCRIPTION"This group is for the counters with a 64-bit version."GROUP cpAtmIfHCEgressIntervalMIBGroup
DESCRIPTION"This group is for the counters with a 64-bit version."
GROUP cpAtmIfHCIngressStatMIBGroup
DESCRIPTION"This group is for the counters with a 64-bit version."::={ cpAtmIfMIBCompliances 1}--
--units of conformance
--
--MIB Groups
--cpAtmIfConfigGroup OBJECT-GROUPOBJECTS{
cpAtmIfMaxBandwidth
}STATUScurrentDESCRIPTION"These are objects related to configuration of propAtm
Interface.
"::={ cpAtmIfMIBGroups 1}cpAtmIfEgressStatMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfEgrRcvClp0Cells,
cpAtmIfEgrRcvClp1Cells,
cpAtmIfEgrClp0DiscCells,
cpAtmIfEgrClp1DiscCells,
cpAtmIfEgrRcvOAMCells,
cpAtmIfEgrRcvEFCICells
}STATUScurrentDESCRIPTION"These are objects related to Egress Statistics of propAtm
interfaces.
"::={ cpAtmIfMIBGroups 2}cpAtmIfEgressIntervalMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfIntEgrRcvClp0Cells,
cpAtmIfIntEgrRcvClp1Cells,
cpAtmIfIntEgrClp0DiscCells,
cpAtmIfIntEgrClp1DiscCells,
cpAtmIfIntEgrRcvOAMCells,
cpAtmIfIntEgrRcvEFCICells
}STATUScurrent
DESCRIPTION"These are objects related to Egress Interval Statistics of
propAtm Interfaces.
"::={ cpAtmIfMIBGroups 3}cpAtmIfIngressStatMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfIngXmtClp0Cells,
cpAtmIfIngXmtClp1Cells,
cpAtmIfIngXmtEFCICells,
cpAtmIfIngXmtOAMCells
}STATUScurrentDESCRIPTION"These are objects related to Ingress Statistics of propAtm
interfaces.
"::={ cpAtmIfMIBGroups 4}cpAtmIfHCEgressStatMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfHCEgrRcvClp0Cells,
cpAtmIfHCEgrRcvClp1Cells,
cpAtmIfHCEgrClp0DiscCells,
cpAtmIfHCEgrClp1DiscCells,
cpAtmIfHCEgrRcvOAMCells,
cpAtmIfHCEgrRcvEFCICells
}STATUScurrentDESCRIPTION"These are objects related to Egress Statistics of propAtm
interfaces.
This group is a 64-bit version of cpAtmIfEgressStatMIBGroup.
"::={ cpAtmIfMIBGroups 5}cpAtmIfHCEgressIntervalMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfHCIntEgrRcvClp0Cells,
cpAtmIfHCIntEgrRcvClp1Cells,
cpAtmIfHCIntEgrClp0DiscCells,
cpAtmIfHCIntEgrClp1DiscCells,
cpAtmIfHCIntEgrRcvOAMCells,
cpAtmIfHCIntEgrRcvEFCICells
}STATUScurrentDESCRIPTION"These are objects related to Egress Interval Statistics of
propAtm Interfaces.
This group is a 64-bit version of
cpAtmIfEgressIntervalMIBGroup.
"::={ cpAtmIfMIBGroups 6}cpAtmIfHCIngressStatMIBGroup OBJECT-GROUPOBJECTS{
cpAtmIfHCIngXmtClp0Cells,
cpAtmIfHCIngXmtClp1Cells,
cpAtmIfHCIngXmtEFCICells,
cpAtmIfHCIngXmtOAMCells
}STATUScurrentDESCRIPTION"These are objects related to Ingress Statistics of propAtm
interfaces.
This group is a 64-bit version of cpAtmIfIngressStatMIBGroup.
"::={ cpAtmIfMIBGroups 7}
END